Single-use manifolds

Single-Use Manifolds, Overmolded in LSR Silicone

One inlet, several outlets, one molded part. We overmold custom single-use manifolds in liquid silicone rubber directly onto your tubing, laid out around your process with plain tube legs or overmolded TC ends.

One molded partInlet, body and outlets together
1/8 to 1 in. IDSilicone, braided or TPE tubing
Gamma sterilisedor non-sterile, cleanroom molded and packed
Illustration of an overmolded silicone Y manifold with an overmolded TC end on the inlet and on both outletsOvermolded TC endsOvermolded Y junctionYour tubing
Illustration of an overmolded Y with overmolded TC ends
The basics

What is a single-use manifold?

A single-use manifold splits one fluid line into several, or brings several lines into one. It is part of a disposable fluid path: installed ready to use, run for a batch or campaign, then replaced.

One molded part at every junction.

A manifold can be assembled from Y-connectors, short lengths of tubing and cable ties, or overmolded, with each junction molded in liquid silicone rubber directly onto the tubing. We make both.

An overmolded Y is one part: there is no barbed connector to fit and tie, and no gap between connector and tube. Branch angles, bore sizes and the overall shape are set around your process, the branches can be laid out to match each other, and the internal volume is kept to what the job needs.

Assembled · 3 Y-connectors, 9 barbed joints, 9 cable ties

Overmolded · 1 molded part at each junction

The same four-outlet layout, built two ways.
Leak paths

Assembly joints are common failure points for contamination.

Molded seals at every port

The silicone is overmolded onto the tubing, so there is no gap between connector and tube to seal by hand.

Assembly time

More components mean more assembly steps, more labour and more points of failure.

One part to fit

A single integrated manifold cuts assembly steps and removes secondary operations.

Consistency

Manual assembly varies seal compression and position from one build to the next.

The same geometry every time

Precision molding gives identical geometry part after part, batch after batch.

Manifold sketcher

Sketch your single-use manifold

One question at a time. We draw your manifold in proportion to the sizes you pick, show the connectors it replaces, and send the whole brief to the quote form in one click.

How it works

How we make your single-use manifold

From your drawing or sketch to finished manifolds, with your approval at each stage.

Send your drawing or sketch

Ports, sizes, what each port connects to, your fluid, pressure and temperature. No drawing yet? Describe the layout.

Proposal and prototype options

We come back with a proposal for the manifold and the options for a first prototype.

Mold made to the agreed design

Once you approve the design, the mold is made to it.

We make your manifolds

We overmold your manifolds onto your tubing, molded and packed in our cleanroom, and supply them non-sterile or gamma sterilised.

Shapes

Overmolded Y, T and cross connectors, TC ends and more

Every manifold is molded to your own layout, port sizes and tubing. These diagrams show the common shapes and port ends.

YSplits one line into two, or brings two into one. The branch angle is set to your layout.
Overmolded TC endA tri-clamp flange molded straight onto the tubing, for the inlet, the outlets or both.
TA side branch at 90 degrees, for example for a sampling, venting or bypass line.
CrossFour ports from one point, molded as one part.
Onto braided hoseSilicone overmolded onto braided hose where a line needs to take more pressure.
Multi-port headerOne inlet feeding several outlets along a straight header, for layouts that need more than a Y or cross.
Vannefold single-use valve manifold block with three motorized valves

Need each outlet switched on and off?

When every line needs its own automated valve, we also supply a single-use diaphragm valve manifold that combines several motorized valves in one block.

See the valve manifold
One molded partNo barbed joints between connector and tube
Gamma or non-sterileSupplied the way your process needs
CleanroomMolded and packed in our cleanroom
Certificates on requestMaterial certificates such as USP Class VI and ISO 10993
Specifications

Single-use manifold specifications

What we can overmold, and how an overmolded manifold compares with one assembled from Y-connectors. We make both.

Molded manifold options

ConstructionLiquid silicone rubber (LSR) overmolded directly onto the tubing as one part
ShapesY, T and cross connectors and multi-port headers, molded to your drawing
Tubing size1/8 in. to 1 in. ID
TubingSilicone, braid-reinforced silicone and thermoplastic (TPE)
Port endsPlain tube legs or overmolded TC (tri-clamp) ends
Hardness10 to 80 Shore A
SupplyNon-sterile or gamma sterilised
ManufactureMolded and packed in our cleanroom
DocumentationMaterial certificates on request, for example USP Class VI and ISO 10993
DesignFrom your drawing or sketch, with an NDA if you need one

Overmolded or assembled?

 OvermoldedAssembled
At each junctionOne molded silicone partA barbed Y-connector with a cable tie on each port
Joint to the tubingSilicone molded directly onto the tubingTubing pushed onto the barbs and tied
LayoutBranch angles and bore sizes set around your processBuilt from standard connector shapes
Internal volumeKept to what the job needsEach connector adds some internal volume
Repeat buildsMolded geometry, the same every timeBuilt by hand to the drawing
Made by usYesYes, as part of complete fluid paths

Single-use manifold assemblies

A manifold is usually one part of a bigger fluid path. We also design and build complete single-use flow paths in Ireland, with the manifold, overmolded or assembled, and the tubing, connectors, valves, bags and filters around it, ready to install.

Applications

Where single-use manifolds are used

Anywhere one line has to become several, or several have to become one, in a closed disposable path.

Splitting a feed

One supply line divided to several bags, filling points or dispensing needles.

Pooling lines

Several lines brought together into one outlet, without a stack of connectors.

Sampling and bypass

Side branches for sampling, venting or bypass, molded into the main line.

Device fluidics

Compact silicone fluid paths for medical and laboratory devices.

Before we quote

What we need to quote your manifold

The sketcher above covers most of it. Anything you cannot answer yet, leave out and we will ask.

Request a quote
  • A drawing or sketch, if you have one
  • New part, or a copy of an existing one
  • Number of ports and their sizes
  • Tubing type: silicone, braided or TPE
  • Port ends: plain tube legs or TC
  • Material and hardness, or our advice
  • Fluid, pressure and temperature range
  • Non-sterile or gamma sterilised supply
  • Packaging needs and quantity
  • Whether you need material certificates
Send us your manifold

Request a quote

Share a drawing, a sketch or your answers from the sketcher. We come back with a proposal and prototype options.

  • Molded to your layout and tubing
  • Plain tube legs or overmolded TC ends
  • Gamma or non-sterile supply
  • Prototype first if you need one
Thank you! Your submission has been received!
Oops! Something went wrong while submitting the form.
FAQ

Single-Use Manifold FAQ

What is a single-use manifold?

A single-use manifold splits one fluid line into several, or brings several lines into one. It is part of a disposable fluid path: installed ready to use, run for a batch or campaign, then replaced.

What is the difference between an overmolded and an assembled manifold?

An assembled manifold is built from barbed Y-connectors, tubing and cable ties. In an overmolded manifold each junction is one silicone part molded directly onto the tubing, so there is no barbed connector to fit and tie. We make both.

What is an overmolded Y connector?

An overmolded Y connector is a Y junction molded in liquid silicone rubber directly onto three lengths of tubing. It splits one line into two, or brings two into one, as one part, with the branch angle set to your layout.

What is an overmolded TC end?

An overmolded TC end is a tri-clamp flange molded in silicone straight onto the end of the tubing, so the line connects to a tri-clamp fitting without a separate barbed TC adapter. It can go on the inlet, the outlets or both.

What are single-use manifold assemblies?

A single-use manifold assembly is a manifold built into a complete fluid path with the tubing, connectors, valves, bags and filters around it. We overmold the manifold, and we also design and build complete single-use flow paths in Ireland.

Which manifold shapes can you make?

Y, T and cross connectors, and multi-port headers with one inlet feeding several outlets. Every manifold is molded to your own layout, port sizes and tubing. For anything else, choose Custom shape in the sketcher.

What tubing sizes can you overmold onto?

Tubing from 1/8 in. to 1 in. inside diameter. Tell us the ID and OD of the tubing you use, and the inlet and outlets can be different sizes.

What tubing can you overmold onto?

Silicone tubing, braid-reinforced silicone tubing and thermoplastic (TPE) tubing. Tell us the tubing you use and we will advise.

Can you overmold onto braided hose?

Yes. We overmold silicone onto braided hose where a line needs to take more pressure.

Can the ports have TC (tri-clamp) ends?

Yes. Each port can be a plain tube leg or an overmolded TC end, with the tri-clamp flange molded straight onto the tubing. The TC size follows the tubing and is confirmed on the quotation.

What silicone hardness is available?

Liquid silicone rubber from 10 Shore A (very soft) to 80 Shore A (firm). We help you choose the hardness for your use.

Are the manifolds supplied sterile?

We supply manifolds non-sterile, for you to sterilise, or gamma sterilised. Tell us which you need when you ask for a quote.

Are the manifolds molded in a cleanroom?

Yes. Our manifolds are molded and packed in our cleanroom.

What material documentation can you provide?

Material certificates are available on request, for example USP Class VI and ISO 10993 documentation for the silicone. Tell us what you need with your enquiry.

How much liquid is left in a manifold?

Every junction holds some internal volume, which is liquid left behind at the end of a run. In an overmolded manifold the bore sizes and branches are set around your process, so the internal volume is kept to what the job needs.

Can we start with a prototype?

Yes. We can start with a prototype so you can try the manifold in your process. Once you approve it, we make the manifolds for you.

Do we need to supply a mold?

No. Send us your drawing or sketch. The mold is made to the agreed design, and we supply the molded manifolds.

What do you need to quote a manifold?

A drawing or sketch if you have one, the number and size of ports, the tubing, the port ends, the material if specified, your fluid, pressure and temperature, non-sterile or gamma supply, packaging needs and the quantity. The sketcher on this page covers most of it.

Can you work under an NDA?

Yes. Send your NDA with your enquiry and we will review it before you share drawings.

Do you also supply single-use valve manifolds?

Yes. Where each line needs its own automated valve, we supply a single-use diaphragm valve manifold that combines several motorized valves in one block. See our single-use valve manifold.